What is an inner forestay?
The inner forestay is typically attached to the mast at the upper spreader and, if not attached permanently, lives next to the mast when not in use. It is made fast to its deck fitting and can be tensioned in a variety of ways.
Is Headstay same as forestay?
On a sailing vessel, a forestay, sometimes called a jibstay, or a headstay, is a piece of standing rigging. It keeps a mast from falling backwards. It is usually attached to the very top of the mast. The other end of the forestay is attached to the bow of the boat.
How do you remove a roller furler?
tie off the jib halyard to the bow cleat or anchor roller. (tight) Loosen a back stay (optional), remove sail see first if the furler will lift. some are split spools, some lift (like CDI) If your doing it over water, use a box cut out and taped around the spool so you don’t loose things.
Does the jib attach to the forestay?
Attach the tack shackle to the tang plate on the deck at the forestay. Start to attach the clips to the forestay. Start with the lowest clip, then unroll to the next. Gradually unroll the jib and attach clips, until all clips are attached.
What is a staysail used for?
The staysail plays three roles: It augments sail power. It helps break down total sail area into smaller working components for ease of handling. The smaller sail units allow for different combinations, giving sailors a variety of options for different conditions.
How much does it cost to re rig a yacht?
For an average 40-foot boat, Cockerill estimates about $100 per foot to re-rig with wire rigging ($4,000), as well as the round-trip cost to haul and launch the boat and unstep and step the rig (an additional $2,500 or so).
How is forestay attached to mast?
On a sailing vessel, a forestay, sometimes just called a stay, is a piece of standing rigging which keeps a mast from falling backwards. It is attached either at the very top of the mast, or in fractional rigs between about 1/8 and 1/4 from the top of the mast.
What is forestay sail?
Definition of forestaysail : the triangular aftermost headsail of a schooner, ketch, or yawl set on the forestay — see sail illustration.
What are the advantages of a cutter rigged sailboat?
A cutter rig breaks the yacht’s sail area down into smaller, easier to manage sails. Winching in two smaller sails is easier than one big sail, as the loads are lighter. If you’ve ever had to winch in a big overlapping genoa after a bad tack, you’ll know the effort and time involved.
What is the difference between a jib and staysail?
On a boat with two staysails the inner sail is called the staysail, and the outer (foremost) is called the jib. This combination of two staysails is called a cutter rig (or in North America a yankee pair) and a boat with one mast rigged with two staysails and a mainsail is called a cutter.
When can I fly a staysail?
In short, the optimum conditions for the staysail (when adding horsepower), are at apparent wind angles of 50-130 with a minimum apparent wind velocity of 10-12 knots. Trim of the staysail is really no different than any other headsail. When reaching, keep in mind the first rule of sail trim: when in doubt, let it out.
How often should yacht rigging be replaced?
approximately every 7-10 years
Normally, the replacement of standing rigging should be done every 10 years. Generally, insurance companies today require the standing rigging be replaced approximately every 7-10 years, depending on how often, or how far the yacht is sailed, they may require the rigging to be replaced earlier than 7 years.
How long does rod rigging last?
From the Rigger – According to industry standards, the anticipated lifespan for stainless steel rigging is 10-12 years for wire and 15-20 years for rod.
What is the difference between a cunningham and a boom vang?
A boom downhaul is used on a boom that connects/attaches to a track mounted gooseneck, track is mounted to the mast. 2. A cunningham is used on a gooseneck that is direct attached to a mast (no track to slide up and down on)…
Can I use rope as an inner forestay?
HMPE/Dyneema Inner forestays are a common topic of conversation amongst offshore sailors. Our tips for using rope as an inner forestay are as follows: Consider / Minimise Chafe – Choose webbing hanks instead of metal.
Is there an HMPE removable inner forestay for a hanse 540?
In conjunction with Quantum Sails Hamble, we were asked to produce an HMPE removable inner forestay system for a Hanse 540. The brief was a lightweight and strong solution but economic compared to a wire forestay.
What material is used to terminate the rope forestay onto the mast?
Produced from high quality 316 stainless steel, these products provided a neat solution to terminate the rope forestay onto the mast. The lower section of the forestay was terminated with an Antal R28.
What is the best alternative to a wire forestay?
The brief was a lightweight and strong solution but economic compared to a wire forestay. Quantum Sails produced the Dacron staysail for use on the Inner forestay. We specified webbing “hanks” to minimise point loads, reducing chafe on the rope forestay.