Where is Httpd default conf?

If you installed httpd from source, the default location of the configuration files is /usr/local/apache2/conf . The default configuration file is usually called httpd. conf .

How do I reset httpd conf to default?

Delete the original and run sudo apt-get reinstall httpd . Go back and see if it created a new . conf , if so then it should be fixed….Command used:

1. vi /etc/httpd/conf/httpd. conf.
2. Updated ServerName to localhost.
3. service httpd restart.
4. chkconfig httpd on.
5. service httpd restart.

Which httpd conf file is Apache using?

The primary Apache configuration file is /etc/httpd/conf/httpd. conf .

What is the default ServerRoot for Apache?

/etc/httpd
By default, ServerRoot is set to “/etc/httpd” for both secure and non-secure servers.

Where is httpd conf Bitnami?

By default, Bitnami applications are accessible at http://SERVER-IP/. The /opt/bitnami/apache2/conf/httpd. conf file contains the configuration of the Apache server.

Where is httpd conf Linux?

The HTTP configuration files are located under the “/etc/httpd” directory, with the main configuration file being the “/etc/httpd/conf/httpd. conf” file. The default document root is “/var/www/html”. Any files or directories below this point will be visible using a browser once you configure the firewall.

What is httpd conf apache2?

Apache is configured by placing configuration directives, such as Listen and ServerName , into a configuration file, which will be read by the Apache executable during the startup. The default configuration file is called ” httpd. conf ” (or ” apache2. conf “) in the directory ” \conf “.

How do I restart Apache bitnami?

Resolution

1. Run the following commands to stop the Apache2 service: sudo systemctl stop apache2 sudo pkill -f apache.
2. Run the following command to start Bitnami’s Apache service: sudo /opt/bitnami/ctlscript.sh restart.
3. Run the following command to prevent the Apache2 service from starting on boot:

How do I start a bitnami LAMP stack?

To get started with Bitnami AMP stacks, we suggest the following steps:

1. Deploy your PHP application. The main directory to deploy your PHP application is /opt/bitnami/apache2/htdocs.
2. Access phpMyAdmin. phpMyAdmin is a PHP-based application intended to handle the administration of MySQL over the Web.

Where is apache2 httpd conf?

Basic Configuration The default configuration file is called ” httpd. conf ” (or ” apache2. conf “) in the directory ” \conf “.

How do I reload httpd?

Type the following command as a root user:

1. apachectl -k graceful.
2. apache2ctl -k graceful.
3. /etc/init.d/httpd graceful.
4. /sbin/service httpd graceful.
5. /etc/init.d/apache2 reload.

Where is Bitnami conf?

Where does Apache install httpd conf by default?

Where does Apache install httpd.conf by default? I thought Apache’s httpd.conf is typically located at /etc/httpd/conf/httpd.conf. But for my installation as described below on Centos 6.4, it is located at /usr/local/apache2/conf/httpd.conf. On top of that, DocumentRoot is set to /usr/local/apache2/htdocs instead of the traditional /var/www/html.

What is the Apache HTTP server configuration file?

Instantly share code, notes, and snippets. # This is the main Apache HTTP server configuration file. It contains the # configuration directives that give the server its instructions.

What does the special value default do in Apache httpd?

Additionally, the special value default can be used to specify Apache httpd’s simple hardcoded message. While not required under normal circumstances, default will restore Apache httpd’s simple hardcoded message for configurations that would otherwise inherit an existing ErrorDocument.

How to configure Apache httpd to respond to a problem or error?

In the event of a problem or error, Apache httpd can be configured to do one of four things, The first option is the default, while options 2-4 are configured using the ErrorDocument directive, which is followed by the HTTP response code and a URL or a message.